Double super diamond

GIDCO FOULKES TRUEING

TOOLS

 

OTHERWISE KNOWN AS DOUBLE SUPER DIAMOND

STRAIGHT..

Under the wheel truing on

all types of surface grinders

as well as cutter and profile

grinders

SIDE..

Removing the runout

increaces the grinding

accuracy and efficiency.

ANGLE

TRUEING...

Angles can be trued on

surface grinders or profile

grinders

REVERSE

TAPERS...

Can be trued if the wheel

head can be tipped, i.e.,

profile grinders, cutter

grinders.

RESINOID BOND ONLY

DIAMOND GRINDING WHEEL

 & CBN

WHEEL TRUEING TOOLS

A major breakthrough in truing / dressing resin diamond and CBN wheels-tests resulted in wheels trued with .0005" flatness without coolant and without removing the wheel from the machine.

                    1/4 x 1-3/4 - use on wheels with up to 1/4 width of diamond or CBN             #1909 - $79.00

                    3/8 x 1-3/4 - use on wheels with up to 3/8 width of diamond or CBN             #1910 - $181.50

                    1/2 x 2 - use on wheels with up to 5/8 width of diamond or CBN                    #1911 - $349.25

                     5/8 x 2 - use on large wheels including centerless (use on O.D. of tool)       #1912 - $463.50

 

Holding Blocks Available:  I. for use with 1/4 and 3/8 trueing tools

                                              II. for use with 3/8 and 1/2 trueing tools

 

All items available from stock

 

Step by Step guide

Gidco-Foulkes Trueing Tool on Resinoid Bonded Diamond and CBN wheels.

 

A wheel trued in this manner will exhibit excellent cutting action on work pieces and leave a correct surface (on accordance with the grit size of the Diamond/CBN wheel).

 

Step 1.   Place trueing tool in holder. Expose not more than 1/2" of trueing tool (on radius dresser             more is allowed.).

 

Step 2.   Turn off woke light to better observe active sparking interface. Turn off coolant.

 

Step 3.   Set up feed (tool travel) to move at a moderate to fast speed, an active sparking interface is the desired effect. Excessive tool wear will be the result of a slow feed setting.

 

Step 4.   Set up downfeed using the chart below. Correct downfeed is determined by the hardness and grit size of the wheel. It's importnt to note at this point that more is better when it comes to calculating the downfeed of the wheel to be trued. DO NOT "BABY" the tool! Cautious downfeeding of the wheel to be trued will simply wear away the trueing tool with no positive effect to the Diamond/CBN wheel.

 

Maximum downfeed (or infeed)

              100 grit or coarser..................................................................   .004"

              180 to 280 grit........................................................................   .003"

               320 grit and finer...................................................................   .002"

 

Step 5.   Allow Gidco-Foulkes trueing Tool to make several passes (2-3) at this position. Trueing in one direction only will leave a crown on wheel.

 

Step 6.   Reduce the downfeed of the wheel with each set of 3 passes across the wheel, for example by going from .001 - .0005- and then to .0002 until the wheel is trued. A wheel trued in this manner will exhibit excellent cutting action on work pieces and leave a correct surface finish (in accordance with the grit size of the Diamond/CBN wheel).

 

Centerless Wheels   For the trueing of centerless diamond wheels use the 5/8" diameter tool and feed tool through its outer diameter as if it were a workpiece. Use feeds as outlined in step 4.

 

Note:   Always wear eye protection and use good grinding practices regarding ventilation.

 

sales@rappindustrialsales.com

105 HUTCHINS LANE

724 368-8006

INFORMATION

Rapp Industrial Sales

Rapp Industrial Sales